Uydumarket Banner  

Gösterilen Mesajlar: 5 mesajdan 1 ile 5 arası

Konu: gi 8120 spark uydu cihazım yazılım yardımı

  1. #1
    Member
    Giriş Tarihi
    11-03-2008
    Mekan
    34 İstanbul
    Yaş
    42
    Mesajlar
    53
    Üye No
    424031

    gi 8120 spark uydu cihazım yazılım yardımı



    galaxy innovation marka bir cihazım var. Linux tabanlı hem de spark özelliği var. yazılımını güncellemek istiyorum. ne yapmam gerekiyor. bağlantı ip sini ve nasıl yazılım atılacağını bilemiyorum. üzerinde 2013 yazılımı olduğu için. ne ip tv sini ne de diğer özelliklerini kullanamıyorum. lütfen yardım edin.

  2. #2
    Senior Member
    Giriş Tarihi
    06-10-2004
    Mekan
    22 Edirne
    Yaş
    51
    Mesajlar
    961
    Kan Grubu
    B Rh ( + )
    Üye No
    32562

    Spark yazılımını online güncellemeden yapabilirsiniz. Menüden spark kısmına girin ve online güncellemeden son yazılıma güncelleyin. Ama bundan önce meü-siste üzerinden net ayarlarını kontrol ediniz; internete bağlı olsun.

  3. #3
    Member
    Giriş Tarihi
    11-03-2008
    Mekan
    34 İstanbul
    Yaş
    42
    Mesajlar
    53
    Üye No
    424031

    sorun işte o. internete bağlanamıyorum. wifi cihazı takarak denedim. olmadı. LAN ethernet kablosundan internete bağlı gözüküyor ama internete giremiyorum. web tv, youtube ve diğer uygulamalara giremiyorum. onun için bu cihaza yeni yazılım atayım diyorum. ne yapmam gerekiyor.

  4. #4
    Advanced Member
    Giriş Tarihi
    08-12-2004
    Mekan
    07 Antalya
    Yaş
    50
    Mesajlar
    1,556
    Kan Grubu
    0 Rh ( + )
    Üye No
    49953

    Merhaba,

    Öncelikle şunu belirteyim; Daha once spark cihaz tecrübem olmadı ama naçizane faydası olur umudu ile:

    Ben sizin için usb bellek ile nasıl yazılım atılacağını aşağıda gördüğünüz şekilde anlatayım.

    1)FAT32 olarak biçimlendirilmiş bir bellek
    2)Bu bellek üzerinde spark adında bir klasör oluşturun.
    3)Indirdiğiniz yazılım içerisindeki dosyaları rardan cikarın(tüm tar.gz ile biten ve version.xml olan dosya spark klasörü içerisine gönderin.Uzantısı tar.gz olanlar tekrar rardan çıkmayacak.O dosyalar olduğu gibi kalır.)
    4)Cihazı şalterden kapatın ve belleği usb yuvasına takın ve cihazı şalterden açın.
    5)Yazılım bitene kadar bekleyin(ekranda "SUCC" yazana kadar)
    6)Cihaz tekrar açılırken bellek cihazdan çıkarılmış olmalı.


    (FAQ)
    Sıkca Sorulan Sorular ve Cevapları

    Q: How do I update is official Software using USB?:
    A: It's very simple:
    1. Make sure your usb flash drive formatted in FAT32.
    2. If the root directory of the flash drive is no spark folder, then create it.
    3. Unzip the firmware files from the archive folder in the drive name: \ spark. As a result, you will have about 10 files with extension tar.gz and 1 Version.xml file.
    4. Turn off the main switch on the AV receiver. Insert the flash drive. Turn on the power.
    5. Wait for the update process. At the end of the process on the display of the receiver appears [SUCC] and the unit will restart

    Q: How to install plugins:
    A: It's very simple:
    1. Download the plugin and unzip
    2. Copy the plugin folder (it should be var folder) in the root of your external drive (flash drive) and connect it to the receiver
    3. Be sure to check the folder structure, it needs to be: C / plugin / var, no extra nested folders, for example, plugin in the plugin should not be
    4. If you connect your drive (flash drive) to the receiver, the system window asking you to update the plug-in should appear
    5. Click Update and click OK
    6. After that, go to the menu and select Plug-ins are plug-ins that you want to activate
    7. Run the plugin is performed on the OK button
    After installing the plug-in can remove the plugin folder from the root of your drive (flash drive), or each time you connect the plugin will ask for updates

    Q: How do I access FTP to the receiver:
    A: It's very simple:
    If you have installed the firmware 1.1.35 or later, go to menu-> System-> networks- Settings> IP Addresses and see how the ip address assigned to the receiver.
    Then connect via FTP to the receiver using the root login and root password, unless of course you have not changed your password.

    Q: How do I get firmware loaded instead of the officially Enigma2?:
    A: It's very simple:
    1. Make sure you have installed the Enigma2 receiver. The new receivers otstutvuet it and you have to install it yourself

    Option 1 (complex):
    1. Turn off the receiver's power toggle switch
    2. Press and hold the OK button on the front panel.
    3. Turn on the AV receiver
    4. After about 5 seconds the display shows [Forc]. Release OK. Then press the button down. The display screen appear [EN16].
    5. Click OK to accept the change selection download. The receiver will automatically reboot.

    Option 2 (simple):
    1. Go to the menu: System-> Factory Settings-> Boot to E2

    Q: I do not have the item in the menu Boot to E2! What to do:
    A: It's very simple:
    1. Go to the menu: System-> Factory Settings-> And very quickly undermining press EPG button 5 2 1 0

    Q: How do I get loaded Official firmware Enigma2 instead?:
    A: It's very simple:
    1. Turn off the receiver's power toggle switch
    2. Press and hold the OK button on the front panel
    3. Turn on the receiver's power.
    4. After about 5 seconds the display shows [Forc]. Release OK. Then press the button up. The display screen appear [SPAR].
    5. Click OK to accept the change selection download. The receiver will automatically reboot.

    Q: How do I update / install Enigma2 using USB?:
    A: It's very simple:

    Option 1 (complex):
    Pre-receiver transfer in download mode Enigma2
    1. Make sure your usb flash drive OTFORMATIROVANY to FAT32 and it was created only one partition.
    2. If the root directory of the flash drive is not enigma2 folder, then create it.
    3. Unzip the firmware files from the archive folder in the drive name: \ enigma2. As a result, you will have 2 files: uImage and e2jffs2.img.
    4. Turn off the main switch on the AV receiver. Insert the flash drive.
    5. Press and hold the OK button on the front panel.
    6. Turn on the receiver's power.
    7. After about 5 seconds the display shows [Forc]. Release OK. Then press the right button. If everything is in order, the display shows [U LD].
    8. If the update is successful, the receiver on the display appears [SUCC] and the unit will restart. If more than 5 minutes and the processes are not completed, it means that something went wrong.

    Option 2 (simple):
    1. Install the plugin E2Upgrade and act in accordance with the instructions in this plugin

    Q: Tell me, is whether the res image output via HDMI and composite (Scart or RCA) at the same time?
    A: It will be broadcast signal, but you need to put 480 or 576 otherwise it will show the HDMI.

    Q: What Internet services supports this appparat?
    A: The list of Internet services is constantly growing. Among the most popular services are supported:

    1. YouTube
    2. YouPorn
    3. Kartina Tv (you must have olachennogo dustupa services to TV picture)
    4. Shoutcast
    5. RSS
    6. Picasso

    A more complete list can be seen in the "Portal"
    Read the Spark portal on the GI 8120 (review)

    Q: Does the receiver's "blind scan" or plugin like Dreama for transponders blind scan?
    A: The firmware is not blind spark posik. In Enigma2 is implemented via plug.

    Q: Is there a web browser in the receiver?
    A: Yes, of course! The receiver is implemented Opera browser

    Q: And in the receiver has a web interface?
    A: Yes, of course! To control the receiver via a Web interface nabereite in the browser http: // ip .adres.vashego.resivera.
    After that, the receiver will not respond to the remote control, as long as you do not close the window vebinterfesa. After that, the ability to control the remote control will be approximately 1 minute

    Q: Can I install my receiver firmware from another receiver on the Platform Fulan Spark STi 7111?
    A: No, because there is protection against this kind of manipulation. Enigma2 is not concerned.

    Q: How to disable the display of subtitles?
    A: It's very simple! Go to Tools-> Language-> Show Subtitles and set to Manual

    Q: How to disable scrolling at the bottom of the list of updates?
    A: It's very simple! Go to the menu Spark-> Configuration-> Settings-> Green button -> Update Notification <OFF>

    Q: While watching the displayed time on the tuner display. Can the receiver to show the channel number or a name?
    A: The name of the channel will not be displayed. Selecting a picture mode "Time / Channel Number" changes in the receiver settings. Also try to press "menu" on the front panel!

    Q: Tell me, if the sound output of the receiver supports a DTS?
    A: Yes, but only as a raw, for decoding external decoder (such as an AV receiver).
    For processing and downmix it into Dolby Digital or PCM requires a license, which is not present.

    Q: Tell me if the receiver supports Bluetooth?
    A: No.

    Q: Tell me how the receiver will show the 3D channels on a 3D TV?
    A: There is no fundamental difference in the output 3D HD and HD channel just for no receiver.
    Channels where transluiruetsya three-dimensional picture, just have 2 images - the so-called stereo pair.
    Depending on the TV model, he or he is offered including 3D mode, or it must be done manually.

    Q: Tell me, does the receiver modem mobile operator brand XXX YYY?
    A: The list of supported modems is in the appropriate topic on the forum.

    Q: Tell me, is it possible to reassign actions knopkok SPARK. For example ask the F1 *** to restart plug-ins?
    A: No.

    Q: Was established in Enigma2 receiver. How am I going to remove it and leave only the Spark?
    A: Please use the plug WLTool

    Q: Tell me, is it possible to watch channels on the network via the WEB browser Sparky?
    A: No. Only in Enigma 2

    Q: Tell me, why Spark switch button "P +" channel occurs on the contrary, I press "P +" program switched descending, I press "P" on the contrary?
    A: In some models, the remote buttons are reversed. Get used.

    Q: Tell me, will it work in my card encoding XXX satellite operator YYY?
    About: This plugin supports MCas majority of Russian operators, but has trouble with maps Tricolor new series. OSCam The plugin works with all cards.

    Q: Tell me, where in the SPARK channel list stored?
    A: List of channels, as well as the settings in the receiver is on the way: root / spark / AppDb /. Separately, the channel list can be downloaded from the receiver in XML format to an external drive.

    Q: Tell me how to make a backup of the channel list?
    A: menu-> System-> Obnovit-> Settings to XML. You choose where to save and presses the red button on the remote (Output)

    Q: Tell me, how to restore the channel list?
    A: menu-> System-> Obnovit-> Settings to XML. Choose a file folder and presses the green button on the remote (Load)

    Q: Tell me how to set up IPTV viewing over UDP in Spark?
    A: You need to install udpxy server.
    Read this post IPTV on Spark- possible?

    Q: How to make a bookmark in Opera on 8120 or do the New Tab page?
    A: We need to change /root/spark/etc/opera/directfb-ui/startpage.html file.
    Read this topic How to make a bookmark in Opera on 8120 or do the New Tab page?

    Q: delete the entire folder into the Plugins / var, how to restore the FTP work?
    A: We need to create a folder / root / plugin / var / ftp
    1. Option
    Create a folder on the flash drive C: \ plugin \ var \ ftp
    res insert and update
    Option 2
    Connect to resu by telnet TGI (TerminalGI Shell) to work with the receiver via telnet
    run the command
    mkdir -p / root / plugin / var / ftp
    Enigma2 yüklemek için
    Installing Enigma2 via TFTP.
    Connect the receiver to the LAN port and the computer on the same network.
    On the laptop:
    0. Install a TFTP server (such as the Open TFTP Server )
    1. Assign a computer ip address 192.168.40.19
    2. Extract the files [uImage] and [e2jffs2.img] in the TFTP server directory (in the Open TFTP Server is C: \ OpenTFTPServer)
    3. Run the TFTP server ( "Run Stand Alone" in Open TFTP Server)
    On the receiver:
    0. Set the system boots - enigma2 (read the FAQ above)
    1. Turn off the main switch on the AV receiver.
    1. Press and hold the OK button on the front panel.
    2. Turn on the receiver's power.
    3. After about 5 seconds the display shows [Forc]. Release OK.
    4. Press the right button. If everything is in order, then appears on the display [T LD]
    5. The TFTP server console at this time will be about connecting and downloading files:

    accepting requests..
    Open TFTP Server MultiThreaded Version 1.64 Windows Built 2001
    starting TFTP...
    alias / is mapped to C:\OpenTFTPServer
    permitted clients: all
    server port range: all
    max blksize: 65464
    default blksize: 512
    default timeout: 3
    file read allowed: Yes
    file create allowed: No
    file overwrite allowed: No
    thread pool size: 1
    detecting Interfaces..
    Listening On: 172.18.34.95:69
    Listening On: 192.168.40.19:69
    Listening On: 127.0.0.1:69
    Client 192.168.40.63:1394 C:\OpenTFTPServer\uImage, 1615 Blocks Served
    Client 192.168.40.63:1044 C:\OpenTFTPServer\e2jffs2.img, 33067 Blocks Served

    6. If the update is successful, the receiver on the display appears [SUCC] and the unit will restart. If more than 5 minutes and the processes are not completed, it means that something went wrong.
    8. Reset the receiver to factory settings.
    Düzenleyen kamaxx : 18-02-2016 at 14:34

  5. #5
    Advanced Member
    Giriş Tarihi
    08-12-2004
    Mekan
    07 Antalya
    Yaş
    50
    Mesajlar
    1,556
    Kan Grubu
    0 Rh ( + )
    Üye No
    49953

    Cihazın yazılımları
    (Nasıl yükleneceği bir üst mesajda yazıyor)

    En güncel olan SPARK7111 yazılımı versiyon 1.2.84


    Uyelik isterse alternatif link



    En güncel powervu açan MCAS dosyası ve k-e-y-l-e-r
    (ana yazılım yüklendi ise bellekten spark klasorunu önce silin)
    Bundeswehr TV (bw tv) & Radio Andernach (13E-11054H27500 + 57E-11007V4880 + 7W-11595V27500)
    SIS-Live
    Astra 4.8 ° E 12149-H-27500 - 12418-H-27500


    Wicardd 1.19 Emu
    (Eğer c line satırı/satırları var ise wicardd.conf içine işlenecek)


    Oscam_Emu
    Düzenleyen kamaxx : 18-02-2016 at 15:54

  6. Merih Banner Alt

Gönderme Kuralları

  • Yeni konu açamazsınız
  • Konuda cevap yazamazsınız
  • Eklenti yapamazsınız
  • Mesajlarınızı düzenleyemezsiniz
  •  
  • BB Kodları Açık
  • Smiley'ler Açık
  • Resim Kodları Açık
  • Video Kodları Açık
  • HTML Kodları Kapalı